在大家使用山東裝載機的過程中，經常會出現裝載機發動機不工作的現象，導致這種現象的原因有很多，比如發動機繼電器的觸摸點氧化、燒蝕、不能閉合，導線銜接處松脫、觸摸不良，蓄電池儲存電量太少等等，那么遇到這種問題時，應該如何處理呢？

1、查看導線銜接處是不是可靠，根據燈火強弱或喇叭音量巨細，初步判別蓄電池是不是放電過多，若放電過多，彌補充電即可。
View wires convergence at is not reliable, according to the strength of the lights or speaker volume size, the initial determination battery is not discharged too much, if discharged too much, you can make up for the charge.
2、查看發動機電磁開關。用導線短接發動機前方接線柱與電磁開關接線柱，若發動機不滾動，闡明電磁開關有毛病，應拆開維修；若滾動，應查看發動繼電器。
Check engine solenoid switch. Front engine with a wire shorting terminals with electromagnetic switch terminal, if the engine does not scroll to clarify faulty solenoid switch should open repair; If the scroll, you should check to launch relay.
3、用導線短接發動機兩接線柱，若發動機仍不滾動，則可斷定毛病在發動機內部，可進一步判別。若發動機正常滾動，闡明毛病部位能夠在電磁開關、發動繼電器。
Engine with a wire shorting two terminals, if the engine is still rolling, you can conclude that the problems inside the engine can be further discrimination. If the engine to normal scrolling, can clarify parts of the electromagnetic switch problems, start relay.
4、查看發動繼電器時，用導線短接其兩個接線柱，若發動機滾動，則闡明發動繼電器有毛病。有能夠常開觸點處氧化而觸摸不良，可用砂紙打磨或替換。
When viewing the launch relay, with a wire shorting its two terminals, if the engine rolling, then clarify the launch relay faulty. There can be normally open contacts of the oxidation and bad touch, use sandpaper or replaced.
5、發動繼電器與電磁開關接線柱之間的銜接導線有搭鐵、斷路或銜接處有松動；也有可能是發動開關失靈，可作進一步查看。
Convergence leads to launch relay and solenoid switch between terminals have grounding, circuit or convergence at loose; is also possible that the ignition switch failure, can be used for further viewing.

山東裝載機：http://m.greennutrition.cn/